在設計假山的時候，可以利用GRC構件制作，利用GRC的好處是，可以真實度更高，紋理更加清晰，可以適用于很多復雜的環境下，減少工程吊裝的時間，效果更真實，那么大家知道如何用GRC制作假山嗎?如何適應環境呢?接下來我們一起來看看吧!
When designing rockery, GRC components can be used to make rockery. The advantage of using GrC is that it can be more realistic, the texture is clearer, and it can be applied to many complex environments. It can reduce the time of engineering hoisting, and the effect is more realistic. So do you know how to make rockery with GRC? How to adapt to the environment? Let's take a look next!
GRC假山模塊制作假山屋的過程如下：1、制作GRC假山模具;2、制造GRC假山模塊;3、在假山房的墻壁上焊接承重架;4、在鋼架上焊接假山模塊;5、接合;6、著色;7、護色。
The process of GRC rockery module making rockery house is as follows: 1. Making GRC rockery mold; 2. Making GRC rockery module; 3. Welding load-bearing frame on the wall of rockery house; 4. Welding rockery module on steel frame; 5. Jointing; 6. Coloring; 7. Color protection.
1、制作GRC假山房屋模具：選擇真山要仿的部分，用硅膠反復涂抹，直到厚度達到2 cm以上。硅膠達到硬度后，用石膏在硅膠上做一個硬模具。
1. Making GRC rockery house mold: first, select the part of the real mountain to be imitated, and apply it repeatedly with silica gel until the thickness reaches more than 2 cm. After the hardness of the silica gel is reached, plaster is used to make a hard mold on the silica gel.
2、制造GRC構件假山模塊：用制作好的模具轉動玻璃鋼假山模塊，將石膏硬模放在底部，硅膠模放在頂部，先在硅膠模內鋪一層快硬硫鋁酸鹽水泥，然后鋪上玻璃網格布，再鋪上2層水泥或直接用噴漿機噴，厚度約3厘米，長寬約1、5米。
2. Manufacturing GRC components rockery module: use the made mold to rotate the glass fiber reinforced plastic rockery module, put the gypsum hard mold on the bottom and the silica gel mold on the top, first lay a layer of fast hardening sulphoaluminate cement in the silica gel mold, then lay the glass mesh cloth, and then lay two layers of cement or spray directly with the shotcreting machine, with the thickness of about 3cm, the length and width of about 1m or 5m.
3、在假山房的墻壁上焊接承重架：在要建假山的房子墻上打洞，間距1m左右。安裝膨脹螺栓，焊接5厘米角鋼。焊接后，做防銹處理。焊接輔助架應與效果圖紙結合，高低位置不應顛倒。
3. Weld the load-bearing frame on the wall of the rockery house: make holes on the wall of the house to be built with a spacing of about 1m. Install expansion bolts and weld 5cm angle steel. After welding, do antirust treatment. The welding auxiliary frame shall be combined with the effect drawing, and the height position shall not be reversed.
4、在鋼架上焊接假山模塊：焊接GRC假山模塊時，注意推遲相鄰兩個GRC假山模塊之間的紋理。將GRC假山模塊與水沖刷線焊接時，水沖刷線應盡可能水平。盡量把接口定位在內角，因?yàn)閮?nèi)角的接口比較好處理。
4. Welding rockery module on steel frame: when welding GRC rockery module, pay attention to delay the texture between two adjacent GRC rockery modules. When welding GRC rockery module with water erosion line, the water erosion line should be as horizontal as possible. Try to locate the interface in the inner corner, because the interface in the inner corner is easier to handle.
5、接合：要特別注意指向假山屋，因?yàn)橹赶蛭恢玫募偕狡け容^粗糙，需要在指向時手動重新紋理化兩塊假山皮。
5. Joint: special attention should be paid to pointing to the rockery house, because the rockery skin pointing to the position is rough, so it is necessary to manually re texture the two rockery skins when pointing.
6、上色：GRC假山房方法多次上色，就像水泥直塑假山房方法一樣。
6. Coloring: the GRC rockery house method is colored many times, just like the cement direct molding rockery house method.
7、護色：粉刷后涂上一層護色劑，可以保護假山屋的顏色不受外界影響，減緩?fù)噬?/div>
7. Color protection: after painting, apply a layer of color protection agent to protect the color of the rockery house from external influence and slow down fading.
利用GRC構件產品制作假山的流程主要是制作GRC假山模具、制造GRC假山模塊、在假山房的墻壁上焊接承重架、在鋼架上焊接假山模塊、接合、著色、護色等7大步驟，這7個步驟是重要的施工環節，在施工的時候，千萬不能忽視，應嚴格按照標準進行施工，保證假山效果更真實。
The process of making rockery with GRC component products mainly includes seven steps: making GRC rockery mold, making GRC rockery module, welding load-bearing frame on the wall of rockery house, welding rockery module on steel frame, jointing, coloring, color protection, etc. these seven steps are important construction links, which should not be ignored during construction. Construction should be carried out in strict accordance with standards to ensure rockery efficiency The results are more real.
